Skip to main content

Recently Updated Pages

2.4 | Tractor / Electrohydraulic Compatibility

COMMAND Manual (EN) 2 | System Overview

COMMAND can make use of either in-built rear tractor electrohydraulic valves, commonly referred t...

Updated 2 months ago by Sathya

8.4 | John Deere StarFire

COMMAND Manual (EN) 8 | Receiver Connection and Configurati...

Applicable to:John Deere StarFire 3000, 6000, 7000 & 7500 GNSS receivers using implement harnessi...

Updated 2 months ago by Sathya

8.3 | NMEA 0183 (RS232)

COMMAND Manual (EN) 8 | Receiver Connection and Configurati...

NMEA 0183 Serial (RS232) capable receivers can be connected to the COMMAND system.  IMPORTANT: If...

Updated 2 months ago by Sathya

8.2 | Trimble FMX/GFX/TMX with Ag25

COMMAND Manual (EN) 8 | Receiver Connection and Configurati...

Applicable to:Trimble FMX, GFX, and TMX displays using NMEA 0183 RS232 output via 12-way DTM port...

Updated 2 months ago by Sathya

8.1 | Modern NMEA 2000 (Case, New Holland, Trimble)

COMMAND Manual (EN) 8 | Receiver Connection and Configurati...

This section covers connection of Novatel-based GNSS receivers using a 12-pin Deutsch interface. ...

Updated 2 months ago by Sathya

7.6 | External Proportional Solenoid Valves — Direct PWM Coil Drive

COMMAND Manual (EN) 7 | Tractor / External Valve Connection...

Applicable to: External proportional valves with solenoid coils driven directly by COMMAND’s PWM ...

Updated 2 months ago by Sathya

10.5 | IMU & Terrain Compensation Issues

COMMAND Manual (EN) 10 | Troubleshooting

Issue Possible Cause Recommended Action Cross-slope compensation not operating correctly ...

Updated 2 months ago by Sathya

1.5 | Important Safety Information

COMMAND Manual (EN) 1 | Introduction

WARNING:The COMMAND system can automatically control hydraulic movement without operator input.En...

Updated 2 months ago by Sathya

4.3 | Power Requirements

COMMAND Manual (EN) 4 | Pre-Installation Requirements

A switched 12V DC power supply with a minimum capacity of 10A is required. The harnessing system ...

Updated 2 months ago by Sathya

2.5 | Selecting System Components

COMMAND Manual (EN) 2 | System Overview

Correct component selection is important for reliable installation and operation of the COMMAND s...

Updated 2 months ago by Sathya

3.3 | Selecting A Machine Profile

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

Profile The profile is used to select the type of implement being used, for detailed information ...

Updated 2 months ago by Sunkyu

10.2 | GNSS & Position Issues

COMMAND Manual (EN) 10 | Troubleshooting

Issue Possible Cause Recommended Action No GNSS position detected Receiver harness disconn...

Updated 2 months ago by Sathya

10.1 | Overview

COMMAND Manual (EN) 10 | Troubleshooting

Before troubleshooting: - Confirm all system components are correctly installed- Verify all conne...

Updated 2 months ago by Sathya

9.2 | John Deere StarFire TCM (3000, 6000, 7000, 7500)

COMMAND Manual (EN) 9 | IMU Installation and Configuration

Applicable to:John Deere StarFire 3000, 6000, 7000 & 7500 receivers with integrated Terrain Compe...

Updated 2 months ago by Sathya

9.1 | TARS-B IMU (T3H-E003)

COMMAND Manual (EN) 9 | IMU Installation and Configuration

Applicable to:Systems where the GNSS receiver does not provide terrain compensation and/or Cross-...

Updated 2 months ago by Sathya

4.4 | ISOBUS Requirements

COMMAND Manual (EN) 4 | Pre-Installation Requirements

COMMAND does not explicitly require the tractor to be fitted with an ISOBUS system to operate; h...

Updated 2 months ago by Sathya

5.3 | Powering COMMAND

COMMAND Manual (EN) 5 | ECU Installation & Mounting

Select the appropriate power supply method based on ECU mounting location. Cab-Mounted ECU COMMAN...

Updated 2 months ago by Sathya

5.2 | Electronic Control Unit (ECU) Installation

COMMAND Manual (EN) 5 | ECU Installation & Mounting

ECU Mounting Overview The COMMAND ECU can be installed in one of three locations depending on the...

Updated 2 months ago by Sathya

4.2 | Tractor Requirements

COMMAND Manual (EN) 4 | Pre-Installation Requirements

Tractor Requirements COMMAND's tractor requirements are as follows: Provide a suitable power sup...

Updated 2 months ago by Sathya

6.1 | Arm/Engage Switch Installation

COMMAND Manual (EN) 6 | Cab Hardware Installation

The COMMAND Arm/Engage Switch is used by the operator to both Arm/Disarm ECU control outputs, and...

Updated 2 months ago by Sathya