Skip to main content

Recently Updated Pages

3.8 | Tuning Automatic Implement Control

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

The purpose of tuning is to achieve stable, accurate Automatic Control that follows the design su...

Updated 3 months ago by Sathya

3.7 | Cylinder Ratio Calibration

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

Overview Cylinder Ratio Calibration compensates for differences in implement movement speeds betw...

Updated 3 months ago by Sathya

3.6 | Valve Threshold Calibration

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

Valve Threshold Calibration establishes the minimum and maximum hydraulic outputs used by Automat...

Updated 3 months ago by Sathya

3.2 | Checking for Software & Firmware Updates

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

Before proceeding with machine configuration and calibration, ensure both the Level COMMAND appli...

Updated 3 months ago by Sathya

3.1 | Connecting to the COMMAND ECU

Level COMMAND Manual (EN) 3 | Dealer Installation & Commissioning

To access COMMAND ECU settings from the Apply View, press "More" at the right side of the screen,...

Updated 3 months ago by Sathya

5.4 | Connecting COMMAND to the ISOBUS

COMMAND Manual (EN) 5 | ECU Installation & Mounting

ECU Mounted In-cab With the COMMAND ECU mounted in-cab: Locate the in-cab 4-way ISOBUS connector...

Updated 3 months ago by Sathya

5.1 | Pre-Installation Preparation

COMMAND Manual (EN) 5 | ECU Installation & Mounting

IMPORTANT: Please ensure you have read the safety information in the previous chapter before comm...

Updated 3 months ago by Sathya

1.1 | Title

Level COMMAND Manual (EN) 1 | Introduction

  Operation & User Manual       2026

Updated 4 months ago by Sathya

10.7 | Support Information

COMMAND Manual (EN) 10 | Troubleshooting

  Office Phone:+61 7 4633 2790 Hardware Support Phone:+61 428 922 668 Email:support@t3rra.com Web...

Updated 4 months ago by Sathya

4.1 | Overview

COMMAND Manual (EN) 4 | Pre-Installation Requirements

All requirements in this section must be confirmed before installing the COMMAND system.  Failure...

Updated 4 months ago by Sathya

1.4 | Important User Information

COMMAND Manual (EN) 1 | Introduction

The COMMAND system must only be installed and operated by individuals trained in its functional a...

Updated 4 months ago by Sathya

2.5 | System Components

Level COMMAND Manual (EN) 2 | System Overview

A Level COMMAND system consists of multiple hardware and software components depending on machine...

Updated 4 months ago by Sathya

2.4 | Hydraulic & Vehicle Interfaces

Level COMMAND Manual (EN) 2 | System Overview

The COMMAND hardware platform supports multiple hydraulic and vehicle interface methods depending...

Updated 4 months ago by Sathya

2.3 | Positioning & Sensor Requirements

Level COMMAND Manual (EN) 2 | System Overview

Level COMMAND uses GNSS positioning data, machine geometry information, and implement orientation...

Updated 4 months ago by Sathya

1.5 | Operator Responsibilities

Level COMMAND Manual (EN) 1 | Introduction

System Usage The COMMAND hardware platform and Level COMMAND operating environment must only be i...

Updated 4 months ago by Sathya

1.3 | Intended Use

Level COMMAND Manual (EN) 1 | Introduction

Level COMMAND is intended for use on supported construction, landforming, and earthmoving machine...

Updated 4 months ago by Sathya

6.2 | Automatic Blade Control

Level COMMAND Manual (EN) 6 | Automatic Control & Surface Behaviour

Automatic Blade Control is the process Level COMMAND uses to guide the implement towards the requ...

Updated 4 months ago by Sathya

5.8 | Choosing a Zeroing Method

Level COMMAND Manual (EN) 5 | Operational Workflows

Selecting the correct zeroing method depends on how the current project was created and whether a...

Updated 4 months ago by Sathya

2.2 | Supported Machine Configurations (Profiles)

Level COMMAND Manual (EN) 2 | System Overview

Level COMMAND supports multiple machine configurations depending on machine type, hydraulic capab...

Updated 6 months ago by Sathya

1.4 | Important Notices

Level COMMAND Manual (EN) 1 | Introduction

Level COMMAND Operators Manual © 2026 T3RRA Notice of Rights No part of this publication may be r...

Updated 6 months ago by Sathya