5.5 | Plane Projects & Surface Creation

Plane Projects allow simple design surfaces to be created without first surveying the entire work area. They are commonly used for creating flat pads, graded surfaces, drain batters and other simple earthworks. Each Plane Project can contain up to four individual Plane surfaces, making it easy to switch between different work areas or design surfaces without creating additional projects.

Creating a Plane Project

From the Apply View, press More > Start Plane. Once the Plane Project has been created, a Planes button will appear on the Apply View. When a Plane surface is selected, the button will display the name of the active Plane.

Selecting and Managing Plane Surfaces

Press Planes on the right side of the Apply View to display the available Plane slots.

Up to four Plane surfaces can be stored within a single Plane Project. Each Plane can have its own:

Name
Size
Origin Point
Primary Slope
Secondary Slope
Elevation Offset

To create a new Plane, select any unused slot labelled Create and the Plane Editor will open on the right side of the screen.

To switch between existing Planes, select the desired Plane from the list. The active Plane is indicated by a yellow outline.

To edit an existing Plane, select it and then select it again to open the Plane Editor. The Plane Editor is used to define and modify all Plane properties, including origin, slopes and survey-based Plane generation.

The Help button in the top-right corner provides a shortcut to this reference page.

Plane Settings

Press Settings within the Plane Editor to configure the Plane name and dimensions. Assigning a meaningful Name makes it easier to identify different work areas within a project.

Plane Width and Height determine the visible extent of the generated Plane surface. These values may be adjusted at any time without affecting the calculated grade of the Plane.

The Delete button removes the currently selected Plane and makes its slot available for reuse.

Defining the Origin Point

The Origin Point is the reference position used to define the Plane elevation and calculate all Plane slopes. It can be thought of as the anchor point of the Plane.

Press Origin within the Plane Editor to define or modify the Origin Point.

The Origin may be defined using:

Use GPS – Sets the Origin to the current implement position and elevation.
Use Marker – Uses an existing marker as the Origin Point.
Manual Coordinates – Allows Latitude, Longitude and Elevation values to be entered directly.

Manual coordinate entry is commonly used when creating a Plane from a surveyed benchmark or known control point.

Once the Origin has been defined, press Okay to return to the Plane Editor. A newly created Plane will initially be flat, with the Origin positioned at the centre of the surface.

Elevation Offset

Elevation Offset allows the entire Plane to be shifted vertically without changing the underlying Plane definition. This is commonly used to quickly raise or lower a design surface when filling, trimming or removing surface irregularities while preserving the existing Plane slopes.

Positive values raise the Plane. Negative values lower the Plane.

Coordinate Formats

The Coordinate Format setting changes how Latitude and Longitude values are displayed. This is a display preference only and does not affect the actual position of the Plane.

Defining the Primary Slope

The Primary Slope defines the main grade direction of the Plane and determines how the surface rises or falls across the work area. Press Slope within the Plane Editor to define the Primary Slope.

The Primary Slope may be created automatically by using a second point on the desired grade surface:

Position the machine at the desired second point on the Plane.
Place the blade on the ground or at the desired design elevation.
Press Use GPS.

Level COMMAND will calculate the slope and direction between the Origin Point and the selected location, then update the Plane surface automatically. Alternatively, the slope percentage and direction may be entered manually if the desired grade is already known.

Once the desired slope has been defined, press Okay to return to the Plane Editor.

Direction

Direction determines the heading along which the Primary Slope is applied.

Slope

Slope determines how steeply the Plane rises or falls along the selected direction. Slope values are expressed as a percentage:

Slope (%) = 100 × Rise ÷ Run

Use GPS

Calculates the slope and direction automatically using the current implement position and the Origin Point. The calculated values may be edited afterwards if required.

Use Marker

Calculates the slope and direction using a previously created Marker and the Origin Point. The calculated values may be edited afterwards if required.

Defining the Secondary Slope

The Second Slope (X-Slope) defines the cross-fall of the Plane at right angles to the Primary Slope. This is commonly used when creating crowned surfaces, side-falls, drain batters or other surfaces requiring grade in two directions.

Press Second Slope within the Plane Editor to define the Secondary Slope. As with the Primary Slope, the Secondary Slope can be generated automatically using a second reference point:

Position the machine at a point representing the desired cross-fall of the Plane.
Place the blade on the ground or at the desired design elevation.
Press Use GPS.

Level COMMAND will calculate the Secondary Slope relative to the Origin Point and update the Plane surface automatically. Alternatively, a known Secondary Slope percentage may be entered manually.

Unlike the Primary Slope, direction does not need to be specified because the Secondary Slope is always applied at 90 degrees to the Primary Slope.

Once the desired Secondary Slope has been defined, press Okay to return to the Plane Editor.

The final Plane surface is calculated using the Origin Point, Primary Slope and Secondary Slope together to define the overall grade of the design surface.

Surveying & Generating A Best Fit Plane

When you are not sure about the slope and heading, you can survey to create a plane of best fit. Once you have your bucket raised, tap the 'Start' button and survey an area. The heading and slope should stabilize as more GPS points are collected. The buttons mentioned below become visible once you have started surveying.

Tap 'Pause' to exclude unwanted GPS points from your survey, but remember to press "Resume" to begin recording survey points again.

Tap 'Stop' when you're done, and the plane will be ready to zero against.

To check the heading and slope values of the plane, simply tap on the plane when it is already selected.